Hot tub pads are convenient that you can find underneath your hot tub. They typically consist of a foam material that easily interlocks. To install a hot tub pad, you’ll have to dig a shallow space under the deck where you want to place your hot tub.
Where is the best location for a hot tub?
Your hot tub can be placed just about anywhere—outdoors or even indoors when practical. You can put it on a deck, patio, rooftop entertaining area, or even under a gazebo. The perfect spot for your hot tub all depends on your home and landscape design and layout, as well as your personal tastes.
Do you need access to all sides of a hot tub?
With today’s Spas you will need to access to the front of the Spa and all the sides. The reality is you may require a plumbing or lighting repair that is only accessible from the side of the Spa, not the front. So just in case you do have a problem, you need access to all sides of the Spa.
Can you put an inflatable hot tub on composite decking?
Composite decking can be built frame-within-a-frame which is a building method dedicated to handling the additional weight. This can be used when building a hot tub to make sure it doesn’t fall apart or collapse under the inclusive weight of the hot tub, water and people that sit in it.
Can I put a hot tub on pavers?
Patio Pavers Are The Ideal Support For Hot Tubs
But before you run out to the hot tub store, consider where you’re going to place it, and what you’re going to place it on. … Once the pavers are in place, they will sweep hydrostatic sand into the joints, and you can set your hot tub up as they leave your driveway.
Do you need to reinforce a deck for a hot tub?
Hot tubs, however, are very heavy, especially when filled with water, and chances are that your existing deck can’t safely support it without additional reinforcement. Fortunately, reinforcing your deck in preparation for a hot tub is a relatively easy task.
What is best base for hot tub?
Now that you know why it’s so important to give your hot tub a base, let’s look at four of the best base and foundation ideas.
- Gravel. With its low cost and ability to provide constant drainage, gravel is a popular choice with many hot tub owners. …
- Concrete/Cement. …
- Decking. …
- Pre-Made Base.
How do I know if my deck is strong enough for a hot tub?
Figuring Out How Much Your Deck Handle
As a general rule of thumb, if you have a deck that’s raised only a couple feet or less, it can support about 100 pounds per square foot. So, if the spa is less than 100 pounds per square foot you likely have nothing to worry about.
How do you level a hot tub for a deck?
Whatever the case, you’ll want to read on for a few useful tips for leveling your hot tub over that uneven surface.
- Use Plastic Shims.
- Use Wooden Shims and a Platform.
- Purchase a Spa Leveler.
- Build a Raised Pad.
- Pour a New Concrete Pad.
- Final Thoughts.
What does a hot tub need to sit on?
A hot tub requires a stable surface — whether it’s a concrete slab, reinforced deck, or firmly compacted soil with crushed gravel. There’s also the option to have the hot tub installed in the ground but that still requires a concrete vault.
How much does a hot tub cost per month?
Modern manufacturers advertise the cost to run their hot tubs at about one dollar per day, with $50 per month at the high end. The energy cost of a hot tub varies based mainly on the heater, which usually draws between 1,500 watts or 6,000 watts.
Can a deck support an inflatable pool?
Some decks can be designed to hold the weight of an inflatable pool filled with water, but that’s not very common. Most decks are designed to hold 40 to 50 pounds per square foot, and one cubic foot of water weighs about 62 pounds. An average inflatable pool will exceed a typical decks weight limit.
What should you put under an inflatable hot tub?
These are the 3 most commonly used foundation types for a hot tub:
- Grass. The grass is definitely one of the most used surfaces under a blow-up hot tub. …
- Concrete pad. This type of foundation is recommended whether or not your tub is an outdoor one or an indoor one. …
- Crushed gravel or stone. …
- Ready-made synthetic tub pads.
Can a hot tub fit through a gate?
(Average Hot Tub is 2 x 2 meter). Check the widths & heights of doorways, passages and gates to make sure the hot tub can pass through. Gates, fences and doors may need to be removed (prior to delivery). Make sure that there is nothing protruding such as drainage pipes, steps or sills that could obstruct the way.
Can you Crane a hot tub over a house?
With the help of a crane, you can lift a hot tub onto balconies or rooftops, over fences or garages… even over your house. The good news is that hot tubs are easy work for crane operators. They are not heavy compared to most crane jobs, and it’s a quick operation (the actual lift only takes a few minutes).
Can a hot tub be lifted over a fence?
In rare cases you might just have no option but to lift the hot tub over the obstacle. This could be from something as minor as a fence or wall, to your entire house. In most cases you won’t need anything as large as a mobile crane. … An entire house then a crane will most likely be required.
How do you prepare a hot tub for installation?
How to Prep the Ground for a Hot Tub
- Select a site for the hot tub. …
- Check the area carefully. …
- Evaluate the distance to a water source, such as a garden hose. …
- Make sure the site is at least five feet away from your electrical panel or outlet.
What is a floating deck?
A floating deck, also called a free standing deck, is simply a deck that’s not attached to any structure, including (of course) your house. … Instead, you can put your deck’s structural members — posts, girders, and joists — on precast pier blocks set directly in the ground.
How do you calculate deck load?
To determine the maximum load capacity of your deck, start by calculating its total area and multiply by 50 psf. So, a 100 sqft deck would be designed to support 5000 lbs. Do not get confused with what weight you might think or want to load the deck with.
How much weight can a 10×10 deck hold?
In short there’s no one right answer to “how much can my deck hold?” However, one rule of thumb to keep in mind while answering the question is that the answer commonly is that if a deck is properly designed, it’s built to hold 50 lbs. per square foot.